Tango Key Programmer Software Update Problem


Matched product:

Original Scorpio-LK Tango Key Programmer V1.115 Supports Daihatsu G Chip/Toyota H 128 Bit Copy Function with Free TANGO OBD Cable

Original Scorpio-LK Tango Key Programmer V1.115 Supports Daihatsu G Chip/Toyota H 128 Bit Copy Function with Free TANGO OBD Cable

Latest price:US$999.00
US$959.004% off
  • Item No. SK80
  • Free Shipping
Scorpio-LK Tango Key Programmer with Basic Software V1.115,supports reading, writing and generating the latest transponders used in the latest vehicle immobilizer technologies. New function of reading Kilometers, VIN and transponder type for all BMW keys has been added to the BMW software module! Immo pin code is also displayed for some car models.

1.TANGO EMULATOR PROGRAM TOYOTA SMART KEY ALL KEYS LOST SUCCESSFULLY  

Here’s Toyota Lexus SMART KEY All Keys Lost programming guide with Tango emulators.

attch-transponder-to-car-07    scorpio-lk-emulators-slk-01-for-tango-key-programmer-parts

Toyota Camry 2013 Smart key 128 bit all keys lost:
Connect Toyota techstream OBD cable with car via vehicle’s diagnostic connector

tango

Open Tango key programmer software on desktop

Click on TangoPlus->Toyota

tango

Click on Settings
Check Pass thru Devices has been selected as MVCI

tango

Click on Connect to car

Click on Read data from car

tango
eeprom reading

Click on Save file to save data

TANGO

 

Keys 88 has been detected
Use SLK-03 transponder

TANGO

Insret Scorpio-LK SLK-03 emulator into Tango
click on Write Emulator on tango software

Tick SLK-03 and press OK

TANGO
Remove SK03 tranposnker and attach it to car Start button

The dashboard indicators flash
Tango Emulator programmed successfully.

2.One of our customers have met problem with the tango key programmer update. He has been using it for 2 years just after update it, And attached is the problem he met with.

Please note that: 

1. The tango software updated for free, the device is original ,you MUST contact the factory to update one time within 28 days ,otherwise it will be locked .If open some special function or special car , it will charge .

2.After generating a new transponder with TANGO Programmer, you don't need any additional diagnostic equipment to program the generated transponder to the car! It will start the car directly, even on new FIAT CODE 2 system, also used in PSA Group vehicles! Only you have to write the new file back into the immobilizer system!

FAQ:

Q: Hardware not found after install the software and driver, how to solve it
A: You need to install the software v1.83 first, then v1.84, next v1.85(install the software from older to newer)
 
Q: Tango key programmer support update for free or not
A: Update free You need to connect the official website to update once within 28 days, otherwise the machine will be blocked. 
If you need special function or work it on special car model, you need to pay for it, you can check specific cost online
 
Q: I reprogram a BMW key, if I can delete the reprogrammed key with Tango
A: No, it do not support this function
 
Q: Is there tokens limitation for Tango Is there any extra cost, such as update cost
A: There is no tokens limitation for Tango. Software update online for free. But if you need special function, or want to work it on 
special car model, you need to pay money to open the authorization
 
Q: Do you have Tango user manual
A: You can check Tango user manual in the menu after software installation

How to Create a Key Step by Step

Firstly, run the key maker interface according to the vehicle and read information in the "Info" window. Watch theData location field describes the memory chip. Find out the chip inside of the immobilizer and read it. Save the read data (dump).

Click the "OPEN IMMOBILIZER FILE" button and load the saved dump.
The program will analyse the dump.
If the dump is correct the "WRITE" button will become active and the "Keys" window will display the range of key numbers that can be created.
Take a look at the "Info" window, the Allowed transponder field.
Ensure you use a transponder exactly the indicated type.
Place the transponder into the coil.
Choose the key position you want create in the "Keys" window.
Click the "WRITE" button.
This starts the writing process and transponder will be stored with the appropriate data.
At this point you may be asked to save a new immobilizer dump.
The program displays a standard File Save dialog where you have to save the data.
After this you will be informed about the new data saved and must be written into the immobiliser.


Write the new dump into the immobilizer. Now it is ready to operate with the created transponder.If you are not asked to save a new file, it means that immobilizer is ready to operate with the created transponder without file replacing.